Oil and Gas:

C9 ACERT™ Water Cooled Manifold Engine

C9 ACERT™ Water-Cooled Manifold
Length
44.4 in.
Width
35.1 in.
Height
41.4 in.
Weight
1844.0 lb

Cat C9 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C9 ACERT engines to deliver excellent performance with low operating costs and emissions.Equipment powered by C9 ACERT engines include workover rigs, pump skids, acidizing units, cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty.C9 ACERT water-cooled manifold engines, with ratings: 242-254 bkW (325-340 bhp) @ 2200 rpm meet IMO Tier II, EPA Non-road Tier 3 equivalent and EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.



Product Specs

  • Dimensions

  • Length
    44.4in.
    Width
    35.1in.
    Height
    41.4in.
    Weight
    1844.0lb
    Length
    44.4in
    Width
    35.1in
    Height
    41.4in
    Weight
    1844lb
  • Capacity for Liquids

  • Lube Oil System (refill)
    8.0gal
    Cooling System
    3.7gal (US)
    Lube Oil System - Refill
    8gal (US)
  • General Specifications

  • Minimum Rating
    325BHP
    Maximum Rating
    340BHP
    Governor and Protection
    Electronic (ADEM™ A4)
    Aspiration
    Turbocharged-Aftercooled
    Displacement
    538in³
    Flywheel and Flywheel Housing
    SAE 1 or 2
    Flywheel Teeth
    113 (SAE 1), 134 (SAE 2)
    Rotation from Flywheel End
    Counterclockwise
    Stroke
    5.9in
    Bore
    4.4in
  • Emissions

  • Emissions
    EPA and CARB Non-Road Tier 3,EU Stage IIIA, EPA Marine Tier 2, IMO Tier II

Equipment

  • Air Inlet System
    • Turbocharger, separate circuit (SCAC) or remote (REMAC)aftercooler
    • Single, right-side, center-mounted turbo with water-cooledturbine housing
    • Air inlet 101.6 mm (4 in) connection type
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Fuel cooled ECU
    • Power compensation for fuel temperature
    • Programmable low and high idle
    • Electronic diagnostics and fault logging
    • Programmable monitoring system (engine speed, temperature,pressure)
    • J1939 broadcast (diagnostic and engine status)
    • Certified electrical control system (hazardous environment only)
    • Derated engine: automatic ambient temperature compensation
  • Cooling System
    • Thermostats and housing, RH forward-facing outlet — 51 mm(2.01 in) connection
    • Jacket water pump — belt-driven, centrifugal
    • Water pump — inlet RH facing downward 63 mm (2.48 in)
  • Exhaust System
    • Exhaust manifold — water-cooled
    • Single, right-side, center-mounted turbo with water-cooledturbine housing
    • Rear facing turbo exhaust 81.8 mm (3.22 in) connection, nonV-band clamp
  • Flywheels And Flywheel Housing
    • Mandatory selection of:SAE No. 1 or SAE No. 2 flywheel and housing, SAE standard rotation
  • Fuel System
    • HEUI fuel system
    • Fuel filter — secondary, LH (2-micron high performance)
    • Fuel transfer pump — left front
    • Fuel priming pump — left front
  • Lube System
    • Crankcase breather — LH
    • Crankcase fumes disposal — with integrated service indicator, LH
    • Oil cooler — RH
    • Oil filter — RH
    • Oil pan — front sump
    • Oil filler — top mounted
    • Oil level gauge — LH side
    • Oil pump — gear-driven
    • Oil valve sampling
    • Preservation of turbocharger, flywheel, and crankcase
  • Power Take-offs
    • Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter,22.3 mm (7/8 in) wide
  • General
    • Vibration damper
    • Lifting eyes
    • Automatic variable timing — electronic
    • Literature
  • Mandatory Options
    • Flywheel housing and flywheel
    • Throttle position sensor and/or throttle control
    • (Non-hazardous environment only)
    • Primary filter/water separator
    • Turbo orientation
  • Air Compressors
    • Air compressors
    • Air compressor governor
  • Air Inlet System
    • Air cleaner
    • Precleaner
    • Air inlet elbow
    • Air shutoffs
  • Charging Systems
    • Charging alternators
    • Alternator mounting
    • Alternator belt tensioner
    • Alternator pulleys
    • Alternator guards
  • Cooling System
    • Radiators
    • Fan drive and pulley — f/u/w radiator packages
    • Fans f/u/w radiator packages
    • Coolant level sensor
    • Fan drive mountings
    • Fan adapters
    • Fan adapter for blower fans
    • Fan pulleys
    • Fan height instructions
    • Vee belts for customer-supplied radiators
    • Suction fans and blower fans
    • Water inlet elbows
    • Dry charge coolant conditioners
  • Emissions Certifications
    • IMO certification
  • Exhaust System
    • Flexible fitting
    • Turbocharger exhaust outlet adapters
    • Elbows, flange, pipes, clamp
    • Rain caps
    • Manifolds
    • Mufflers
  • Flywheels And Flywheel Housing
    • Crankshaft seal
  • Fuel System
    • Flexible fuel lines
    • Water separator and fuel filters
    • Fuel cooler
  • Instrumentation
    • Gauges and instrument panels
    • Interconnect harness
    • Voltmeters
    • Gauge mounting
    • Ammeter
  • Lube System
    • Oil pans
    • Drain and cover
    • Oil level gauges
    • Remote oil filter
    • Oil fillers
    • Lubricating oil
    • Fumes disposal
  • Mounting System
    • Structural steel base
    • Engine support — front and rear
  • Power Take-offs
    • Enclosed clutch
    • Clutch supports
    • Flywheel stub shaft
    • Hydraulic pump drives
    • Hydraulic gear pumps
  • Starting System
    • Starting aids
    • Electric starting motors — 12V and 24V
    • Battery sets — 12V and 24V (dry)
    • Battery cable
  • General
    • Tool set

Request a Quote

Find a Boyd CAT
Location or Rep Near You