Diesel Fire Pumps:
Cat® 3406C Fire Pump Engine
Contact Us About This Product
Click a link to download the document:
- Minimum Power
- 292.0 bhp
- Maximum Power
- 482.0 bhp
- Emissions
- Non-Certified. Available for global non-regulated areas. FM Approved, UL Listed
- Rated Speed
- 1750-2300 rpm
The Cat® 3406C Industrial Diesel Fire Pump Engine is offered in ratings ranging from 218-359 kW (292-482 hp) @ 1750-2300 rpm. These ratings are non-certified and available for global non-regulated areas. They are FM Approved and UL Listed. Additional 3406C ratings with or without radiators are available, but not FM approved or UL listed. Starting on demand is a must for a fire pump engine – always. Cat® fire pump engines have a reputation for reliable starts and long efficient service.
Product Specs
-
Power Rating
- Minimum Power
- 292.0bhp
- Maximum Power
- 482.0bhp
- Rated Speed
- 1750-2300 rpm
- Minimum Power
- 292HP
- Maximum Power
- 482HP
- Rated Speed
- 1750-2300 rpm
-
Emission Standards
- Emissions
- Non-Certified. Available for global non-regulated areas. FM Approved, UL Listed
- Emissions
- Non-Certified. Available for global non-regulated areas. FM Approved, UL Listed
-
General
- Aspiration
- Turbocharged Aftercooled
- Compression Ratio
- 14.5:1
- Rotation (from flywheel end)
- Counterclockwise
- Engine Configuration
- Inline 6, 4-Stroke-Cycle Diesel
- Bore
- 137.2 mm (5.4 in)
- Stroke
- 165.1 mm (6.5 in)
- Displacement
- 14.6 L (893 in³)
- Cooling System - Capacity
- 32.2 L (34 qt)
- Lube System - Refill
- 34.1 L (36 qt)
- Bore
- 5.4in
- Stroke
- 6.5in
- Displacement
- 893in³
- Aftertreatment
- -
- Aspiration
- Turbocharged Aftercooled
- Compression Ratio
- 14.5:1
- Rotation from Flywheel End
- Counterclockwise
-
Engine Dimensions - Approximate
- Length
- 65.4in
- Height
- 52.6in
Equipment
-
- Air Inlet System
-
- Dry or watercooled manifold and turbocharger
-
- Charging System
-
- Charging Alternator, 24 volt, 35 amp
-
- Control System
-
- Hydra-mechanical governor
-
- Cooling System
-
- Thermostats and housing
- Jacket water pump, gear driven, centrifugal
- Heat exchanger
- Expansion tank
- FM Required Raw Water Cooling Loops: 1.5" iron, horizontal or vertical, 1.5" 316 stainless steel, horizontal or vertical
- Optional Radiator, not UL listed or FM approved
-
- Exhaust System
-
- Exhaust manifold, water-cooled (wet) or dry
- Exhaust elbow, dry, 152 mm (6 in), 4 bolt flange
-
- Flywheels And Flywheel Housing
-
- SAE No. 1 flywheel
- SAE No. 1 flywheel housing
- SAE standard rotation
-
- Fuel System
-
- Fuel filter, LH
- Fuel transfer pump
- Primary fuel filter / water separator
-
- Instrumentation
-
- Instrument panel, LH
- Engine oil pressure gauge
- Fuel pressure gauge
- Water temperature gauge
- Service meter
-
- Lube System
-
- Crankcase breather
- Oil cooler
- Lube oil filter
- Oil filler in valve cover and dipstick, both RH
- Rear sump oil pan
- Oil filler in valve cover
- Dipstick
-
- Mounting System
-
- Supports
-
- Power Take-offs
-
- Flywheel stub shaft
-
- Protection System
-
- Stop-Start System, automatic (compatible with NFPA 20 requirements, able to be energized from either of two battery sources and capable of manual starter actuation)
-
- General
-
- Vibration damper and guard
- Lifting eyes
- Paint - fire pump red, optional radiator painted black