Cat® wheel loaders set the standard for productivity, fuel efficiency and operator comfort. The Cat 907 Compact Wheel Loader has a high torque C2.8 engine that works in conjunction with an intelligent hystat power train to deliver exceptional fuel efficiency. “Shift on the go†locking differentials and hydrostatic transmission provide smooth and powerful operation while increasing the efficiency of machine cycles.
all new cab with seat mounted controls and integrated display screen
with "shift on the go" transmission
for application specific configurations including factory and aftermarket options
| Maximum Gross Power | 74.7 hp |
|---|---|
| Engine Model | Cat C2.8* |
| Maximum Engine Speed | 2550 rpm |
| Maximum Gross Power - Rated Engine Speed | 2400 r/min |
| Maximum Gross Power - SAE J1995 | 74.7 hp |
| Maximum Gross Power - ISO 14396 | 74.3 hp |
| Maximum Gross Power - ISO 14396 (metric) | 75.3 mhp |
| Rated Net Power - Rated Engine Speed | 2400 r/min |
| Rated Net Power - SAE J1349 | 72.7 hp |
| Rated Net Power - ISO 9249 | 72.1 hp |
| Rated Net Power - 2,400 rpm - ISO 9249 (metric) | 73.1 mhp |
| Maximum Gross Torque - SAE J1995 | 222 lb/ft |
| Maximum Gross Torque - ISO 14396 | 221 lb/ft |
| Maximum Net Torque - SAE J1349 | 218 lb/ft |
| Maximum Net Torque - ISO 9249 | 217 lb/ft |
| Displacement | 171 in³ |
| Bore | 3.54 in |
| Stroke | 4.33 in |
| Note | *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. |
| Note (1) | Advertised power is tested per the specified standard in effect at the time of manufacture. |
| Note (2) | Net power advertised is the power available at the flywheel. |
| Note (3) | #Maximum gross and net torque measured at 1,600 rpm. |
| Operating Weight | 12765 lb |
|---|
| Bucket Capacities | 0.75-1.55 m³ (1.0-2.0 yd³) |
|---|---|
| Bucket Capacities - General Purpose | 0.80-1.35 m³ (1.0-1.7 yd³) |
| Bucket Capacities - Light Material | 1.25-1.55 m³ (1.6-2.0 yd³) |
| Multi-Purpose | 0.75-1.1 m³ (1.0-1.4 yd³) |
| Note | Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration. |
| Note (1) | Bucket capacities stated include BOCE, in line with ISO 7546. |
| Fuel Tank | 24 Gal |
|---|---|
| Cooling System | 3.2 Gal |
| Engine Crankcase | 2.3 Gal |
| Axles - Front Center Differential | 2.3 Gal |
| Axles - Rear Center Differential | 2.3 Gal |
| Hydraulic System - Including Tank | 17.8 Gal |
| Hydraulic Tank | 11.8 Gal |
| Transmission | 0.6 Gal |
| Note | No Diesel Exhaust Fluid (DEF) fluid needed on this size engine. |
| Front | Fixed (standard), Locking Differential (optional) |
|---|---|
| Rear | Fixed (standard), Locking Differential (optional) |
| Note | Oscillation of ±11 degrees via hitch between front and rear frames. |
| Steering Articulation Angle - Each Direction | 39 ° |
|---|---|
| Maximum Flow - Steering Pump | 12.3 gpm |
| Maximum Working Pressure - Steering Pump | 3336 psi |
| Steering Cycle Times – (full left to full right) – at High Idle | 2.8 s |
| Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left | 3.25 turns or 4.00 turns |
| Forward and Reverse - Speed Range Creep# | 6 mile/h |
|---|---|
| Forward and Reverse - Speed Range 1* | 6 mile/h |
| Forward and Reverse - Speed Range 2** - High Speed | 10.5 mile/h |
| Forward and Reverse - Speed Range 2** - Standard | 12 mile/h |
| Forward and Reverse - Speed Range 3*** | 25 mile/h |
| Note | #Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph). |
| Note (1) | *Creep function not available in this gear or above. |
| Note (2) | **Max speed dependent on model and configuration (standard vs. high speed transmission). |
| Note (3) | ***Reverse is 30 km/h (19 mph). |
| Tire Size - Standard | *405/70 R18 SPT9 |
|---|---|
| Tire Size - Optional | 405/70 R18 Powerloads |
| Tire Size - Optional (1) | 340/80 R18 XMCL/Bibload |
| Tire Size - Optional (2) | 340/80 R18 TRI 2 |
| Tire Size - Optional (3) | 40X14-20 TL, SM/TR |
| Tire Size - Optional 4 | 340/80 R18 Duraforce |
| Note | *This tire has been used for all dimension, stability and performance data. |
| Note (1) | Other tire choices are available. Contact your Cat dealer for details. |
| Note (2) | Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model. |
| ROPS | ISO 3471:2008 |
|---|---|
| FOPS | ISO 3449:2005 Level II |
| Note (1) | Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU. |
| Note (2) | The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 71 dB(A). |
| Note (3) | *Measurements were conducted with the cab doors and windows closed. |
| Note (4) | The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 101 dB(A). 99 dB(A) Low Sound – Option available. |
| Main Relief - 1st Auxiliary (3rd slice) | 3408 psi |
|---|---|
| Main Relief - 1st Auxiliary (3rd slice) - Standard Flow* | 21 gpm |
| Main Relief - 1st Auxiliary (3rd slice) - High Flow* | 32 gpm |
| Main Relief - 2nd Auxiliary (4th slice) | 3408 psi |
| Main Relief - 2nd Auxiliary (4th slice) - Flow | 12 gpm |
| Hydraulic Cycle Time - Rackback | 2.2 s |
| Hydraulic Cycle Time - Lift | 5 s |
| Hydraulic Cycle Time - Dump | 1.6 s |
| Hydraulic Cycle Time - Float Down | 2.8 s |
| Note | * Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display. |
| Height: Ground to Cab** | 8.5 ft |
|---|---|
| Height: Ground to Beacon** | 9.08 ft |
| Height: Ground Axle Center** | 1.58 ft |
| Height: Ground Clearance** | 1 ft |
| Length: Overall* | 17.58 ft |
| Length: Rear Axle to Bumper | 4.58 ft |
| Length: Hitch to Front Axle | 3.58 ft |
| Length: Wheel Base | 7.08 ft |
| Length: Front Axle to Front of Coupler | 3.5 ft |
| Clearance: Bucket at 45° * | 8.25 ft |
| Clearance: Load over Height** | 9.5 ft |
| Clearance: Level Bucket** | 9.92 ft |
| Height: Bucket Pin** | 10.67 ft |
| Height: Overall** | 13.5 ft |
| Reach: Bucket at 45° * | 2.33 ft |
| Carry Height: Bucket Pin | 1.08 ft |
| Dig Depth** | 0.33 in |
| Width: Bucket | 6.75 ft |
| Width: Tread Center | 4.67 ft |
| Turning Radius: Over Bucket | 14.75 ft |
| Width: Over Tires | 6.07 ft |
| Turning Radius: Outside of Tires | 12.92 ft |
| Turning Radius: Inside of Tires | 6.75 ft |
| Rack Angle at Full Lift | 56° |
| Dump Angle at Full Lift | 45° |
| Rack Angle at Carry | 51° |
| Departure Angle - Degrees | 30° |
| Articulation Angle - Degrees | 39° |
| Operating Weight: Bucket ^ | 12689 lb |
| Tipping Load - Straight - ISO 14397-1 †| 9773 lb |
| Tipping Load - Full Turn - ISO 14397-1 †| 8235 lb |
| Operating Weight: Carriage and Tines ^^ | 12220 lb |
| Tipping Load - Straight †| 7807 lb |
| Tipping Load - Full Turn †| 6569 lb |
| 80% of Tip: Firm and Level EN474-3 ††| 5255 lb |
| Note (1) | *Vary with bucket |
| Note (2) | **Vary with tire |
| Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. |
| Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
| Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
| Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
| Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
| Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). |
| Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9. |
| Height - Ground to Cab | 8.5 ft |
|---|---|
| Height: Ground to Beacon** | 9.08 ft |
| Height: Ground Axle Center** | 1.58 ft |
| Height - Ground Clearance | 1 ft |
| Length - Overall with Bucket | 18.17 ft |
| Length: Rear Axle to Bumper | 4.58 ft |
| Length: Hitch to Front Axle | 3.58 ft |
| Length - Wheel Base | 7.08 ft |
| Length: Front Axle to Front of Coupler | 4.33 ft |
| Clearance - Bucket at 45° | 7.83 ft |
| Clearance: Load over Height** | 9.5 ft |
| Clearance - Level Bucket | 9.92 ft |
| Height - Bucket Pin | 10.67 ft |
| Height: Overall** | 13.83 ft |
| Reach - Bucket at 45° | 2.67 ft |
| Carry Height: Bucket Pin | 1.17 ft |
| Dig Depth | 3 in |
| Width - Bucket | 6.75 ft |
| Width - Tread Center | 4.67 ft |
| Turning Radius - Over Bucket | 15 ft |
| Width - Over Tires | 6.08 ft |
| Turning Radius: Outside of Tires | 12.92 ft |
| Turning Radius - Inside Tire | 6.75 ft |
| Rack Angle at Full Lift | 51° |
| Dump Angle at Full Lift | 50° |
| Rack Angle at Carry | 46° |
| Departure Angle - Degrees | 30° |
| Articulation Angle - Degrees | 39° |
| Operating Weight: Bucket ^ | 12897 lb |
| Tipping Load – Straight – ISO 14397-1 †| 8653 lb |
| Tipping Load – Full Turn – ISO 14397-1 †| 7257 lb |
| Operating Weight: Carriage and Tines ^^ | 12414 lb |
| Tipping Load - Straight †| 7416 lb |
| Tipping Load - Full Turn †| 6266 lb |
| 80% of Tip: Firm and Level EN474-3 ††| 5013 lb |
| Note (1) | *Vary with bucket |
| Note (2) | **Vary with tire |
| Note (3) | ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket. |
| Note (4) | ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center). |
| Note (5) | †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing. |
| Note (6) | ††Full compliance to EN474-3 and SAE J1197. |
| Note (7) | #HPL-A weight, tipping and rated loads are within 1% of the HPL-V. |
| Note (8) | Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines, (tire supplier variability can impact dimensions by 2%). |
| Note (9) | Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9. |
| Recyclability | 93% |
|---|
